The merchandise covered by this investigation is stainless steel sheet and strip, whether in coils or straight lengths. Stainless steel is an alloy steel containing, by weight, 1.2 percent or less of carbon and 10.5 percent or more of chromium, with or without other elements. The subject sheet and strip is a flatrolled product with a width that is greater than 9.5 mm and with a thickness of 0.3048 mm and greater but less than 4.75 mm, and that is annealed or otherwise heat treated, and pickled or otherwise descaled. The subject sheet and strip may also be further processed (e.g., cold-rolled, annealed, tempered, polished, aluminized, coated, painted, varnished, trimmed, cut, punched, or slit, etc.) provided that it maintains the specific dimensions of sheet and strip set forth above following such processing. The products described include products regardless of shape, and include products of either rectangular or non-rectangular crosssection where such cross-section is achieved subsequent to the rolling process, i.e., products which have been ‘‘worked after rolling’’ (e.g., products which have been beveled or rounded at the edges). For purposes of the width and thickness requirements referenced above: (1) Where the nominal and actual measurements vary, a
product is within the scope if application of either the nominal or actual measurement would place it within the scope based on the definitions set forth above; and (2) where the width and thickness vary for a specific product (e.g., the thickness of certain
products with non-rectangular cross-section, the width of certain products with nonrectangular shape, etc.), the measurement at its greatest width or thickness applies.
All products that meet the written physical description, and in which the chemistry quantities do not exceed any one of the noted element levels listed above, are within the scope of this investigation unless specifically excluded. Subject merchandise includes stainless steel sheet and strip that has been further processed in a third country, including but not limited to cold-rolling, annealing, tempering, polishing, aluminizing, coating, painting, varnishing, trimming, cutting, punching, and/or slitting, or any other processing that would not otherwise remove the merchandise from the scope of the investigation if performed in the country of manufacture of the stainless steel sheet and strip.
Excluded from the scope of this investigation are the following: (1) Sheet and strip that is not annealed or otherwise heat treated and not pickled or otherwise descaled; (2) plate (i.e., flat-rolled stainless steel products of a thickness of 4.75 mm or more); and (3) flat wire (i.e., cold-rolled sections, with a mill edge, rectangular in shape, of a width of not more than 9.5 mm).
The products under investigation are currently classifiable under Harmonized Tariff Schedule of the United States (HTSUS) subheadings 7219.13.0031, 7219.13.0051, 7219.13.0071, 7219.13.0081, 7219.14.0030, 7219.14.0065, 7219.14.0090, 7219.23.0030, 7219.23.0060, 7219.24.0030, 7219.24.0060, 7219.32.0005, 7219.32.0020, 7219.32.0025, 7219.32.0035, 7219.32.0036, 7219.32.0038, 7219.32.0042, 7219.32.0044, 7219.32.0045, 7219.32.0060, 7219.33.0005, 7219.33.0020,
7219.33.0025, 7219.33.0035, 7219.33.0036, 7219.33.0038, 7219.33.0042, 7219.33.0044, 7219.33.0045, 7219.33.0070, 7219.33.0080, 7219.34.0005, 7219.34.0020, 7219.34.0025, 7219.34.0030, 7219.34.0035, 7219.34.0050, 7219.35.0005, 7219.35.0015, 7219.35.0030, 7219.35.0035, 7219.35.0050, 7219.90.0010, 7219.90.0020, 7219.90.0025, 7219.90.0060, 7219.90.0080, 7220.12.1000, 7220.12.5000, 7220.20.1010, 7220.20.1015, 7220.20.1060, 7220.20.1080, 7220.20.6005, 7220.20.6010, 7220.20.6015, 7220.20.6060, 7220.20.6080, 7220.20.7005, 7220.20.7010, 7220.20.7015, 7220.20.7060, 7220.20.7080, 7220.90.0010, 7220.90.0015, 7220.90.0060, and 7220.90.0080. Although the HTSUS subheadings are provided for convenience and customs purposes, the written description of the scope of this proceeding is dispositive. |