For the purposes of this Suspension Agreement, “hot-rolled steel” means certain hot-rolled flat-rolled carbon-quality steel products of a rectangular shape, of a width of 0.5 inch or greater, neither clad, plated, nor coated with metal and whether or not painted, varnished, or coated with plastics or other non-metallic substances, in coils (whether or not in successively superimposed layers) regardless of thickness, and in straight lengths, of a thickness less than 4.75 mm and of a width measuring at least 10 times the thickness.
Universal mill plate (i.e., flat-rolled products rolled on four faces or in a closed box pass, of a width exceeding 150 mm but not exceeding 1250 mm and of a thickness of not less than 4 mm, not in coils and without patterns in relief) of a thickness not less than 4.0 mm is not included within the scope of this agreement.
Specifically included in this scope are vacuum degassed, fully stabilized (commonly referred to as interstitial-free (“IF”)) steels, high strength low alloy (“HSLA”) steels, and the substrate for motor lamination steels. IF steels are recognized as low carbon steels with micro-alloying levels of elements such as titanium and/or niobium added to stabilize carbon and nitrogen elements. HSLA steels are recognized as steels with micro-alloying levels of elements such as chromium, copper, niobium, titanium, vanadium, and molybdenum. The substrate for motor lamination steels contains micro-alloying levels of elements such as silicon and aluminum.
Steel products to be included in the scope of this agreement, regardless of HTSUS definitions, are products in which: 1) iron predominates, by weight, over each of the other contained elements; 2) the carbon content is 2 percent or less, by weight; and 3) none of the elements listed below exceeds the quantity, by weight, respectively indicated: 1.80 percent of manganese, or 1.50 percent of silicon, or 1.00 percent of copper, or 0.50 percent of aluminum, or 1.25 percent of chromium, or 0.30 percent of cobalt, or 0.40 percent of lead, or 1.25 percent of nickel, or 0.30 percent of tungsten, or 0.012 percent of boron, or 0.10 percent of molybdenum, or 0.10 percent of niobium, or 0.41 percent of titanium, or 0.15 percent of vanadium, or 0.15 percent of zirconium.
All products that meet the physical and chemical description provided above are within the scope of this agreement unless otherwise excluded. For examples of hot-rolled steel coil that is outside and/or specifically excluded from the scope of this agreement, see the Federal Register notice for this agreement which provides charts indicating the chemical, physical, and mechanical specifications of excluded hot-rolled steel coil. Additional examples of products excluded from the scope are described as follows.:
_ Alloy hot-rolled steel products in which at least one of the chemical elements exceeds those listed above
(including e.g., ASTM specifications A543, A387, A514, A517, and A506).
_ SAE/AISI grades of series 2300 and higher.
_ Ball bearing steels, as defined in the HTSUS.
_ Tool steels, as defined in the HTSUS.
_ Silico-manganese (as defined in the HTSUS) or silicon electrical steel with a silicon level exceeding 1.50 percent.
_ ASTM specifications A710 and A736.
_ USS Abrasion-resistant steels (USS AR 400, USS AR 500).
_
_ Hot-rolled dual phase steel, phase-hardened, primarily with a ferritic-martensitic microstructure, contains 0.9 percent up to and including 1.5 percent silicon by weight, further characterized by either (i) tensile strength between 540 N/mm˛ and 640 N/mm˛ and an elongation percentage greather than or equal to26 percent for thicknesses of 2 mm and above, or (ii) a tensile strength between 590 N/mm˛ and 690 N/mm˛ and an elongation percentage greater than or euqal to 25 percent for thicknesses of 2mm and above.
_ Hot-rolled bearing quality steel, SAE grade 1050, in coils, with an inclusion rating of 1.0 maximum per ASTM E 45, Method A, with excellent surface quality and chemistry restrictions as follows: 0.012 percent maximum phosphorus, 0.015 percent maximum sulfur, and 0.20 percent maximum residuals including 0.15 percent maximum chromium.
Grade ASTM A570-50 hot-rolled steel sheet in coils or cut lengths, width of 74 inches (nominal, within ASTM tolerances), thickness of 11 gauge (0.119 inches nominal), mill edge and skin passed, with a minimum copper content of 0.20 percent.
The covered merchandise is classified in the Harmonized Tariff Schedule of the United States (“HTSUS”) at subheadings: 7208.10.15.00, 7208.10.30.00, 7208.10.60.00, 7208.25.30.00, 7208.25.60.00, 7208.26.00.30, 7208.26.00.60, 7208.27.00.30, 7208.27.00.60, 7208.36.00.30, 7208.36.00.60, 7208.37.00.30, 7208.37.00.60, 7208.38.00.15, 7208.38.00.30, 7208.38.00.90, 7208.39.00.15, 7208.39.00.30, 7208.39.00.90, 7208.40.60.30, 7208.40.60.60, 7208.53.00.00, 7208.54.00.00, 7208.90.00.00, 7210.70.30.00, 7210.90.90.00, 7211.14.00.30, 7211.14.00.90, 7211.19.15.00, 7211.19.20.00, 7211.19.30.00, 7211.19.45.00, 7211.19.60.00, 7211.19.75.30, 7211.19.75.60, 7211.19.75.90, 7212.40.10.00, 7212.40.50.00, 7212.50.00.00. Certain hot-rolled flat-rolled carbon-quality steel covered include: vacuum degassed, fully stabilized; high strength low alloy; and the substrate for motor lamination steel may also enter under the following tariff numbers: 7225.11.00.00, 7225.19.00.00, 7225.30.30.50, 7225.30.70.00, 7225.40.70.00, 7225.99.00.90, 7226.11.10.00, 7226.11.90.30, 7226.11.90.60, 7226.19.10.00, 7226.19.90.00, 7226.91.50.00, 7226.91.70.00, 7226.91.80.00, and 7226.99.01.80. Although the HTSUS subheadings are provided for convenience and Customs purposes, the written description of the covered merchandise is dispositive.
|