The merchandise subject to these orders is certain hot-rolled
products of carbon steel and alloy steel, in coils, of approximately
round cross section, 5.00 mm or more, but less than 19.00 mm, in solid
cross-sectional diameter.
Specifically excluded are steel products possessing the above-noted
physical characteristics and meeting the Harmonized Tariff Schedule of
the United States (HTSUS) definitions for (a) stainless steel; (b) tool
steel; (c) high nickel steel; (d) ball bearing steel; and (e) concrete
reinforcing bars and rods. Also excluded are (f) free machining steel
products (i.e., products that contain by weight one or more of the
following elements: 0.03 percent or more of lead, 0.05 percent or more
of bismuth, 0.08 percent or more of sulfur, more than 0.04 percent of
phosphorus, more than 0.05 percent of selenium, or more than 0.01
percent of tellurium).
Also excluded from the scope are 1080 grade tire cord quality wire
rod and 1080 grade tire bead quality wire rod. This grade 1080 tire
cord quality rod is defined as: (i) grade 1080 tire cord quality wire
rod measuring 5.0 mm or more but not more than 6.0 mm in cross-
sectional diameter; (ii) with an average partial decarburization of no
more than 70 microns in depth (maximum individual 200 microns); (iii) having
no non-deformable inclusions greater than 20 microns and no deformable
inclusions greater than 35 microns; (iv) having a carbon
segregation per heat average of 3.0 or better using European Method NFA
04-114; (v) having a surface quality with no surface defects of a
length greater than 0.15 mm; (vi) capable of being drawn to a diameter
of 0.30 mm or less with 3 or fewer breaks per ton, and (vii) containing
by weight the following elements in the proportions shown: (1) 0.78
percent or more of carbon, (2) less than 0.01 percent of aluminum, (3)
0.040 percent or less, in the aggregate, of phosphorus and sulfur, (4)
0.006 percent or less of nitrogen, and (5) not more than 0.15 percent,
in the aggregate, of copper, nickel and chromium.
This grade 1080 tire bead quality rod is defined as: (i) grade 1080
tire bead quality wire rod measuring 5.5 mm or more but not more than
7.0 mm in cross-sectional diameter; (ii) with an average partial
decarburization of no more than 70 microns in depth (maximum individual
200 microns); (iii) having no non-deformable inclusions greater than 20 microns
and no deformable inclusions greater than 35 microns; (iv)
having a carbon segregation per heat average of 3.0 or better using
European Method NFA 04-114; (v) having a surface quality with no
surface defects of a length greater than 0.2 mm; (vi) capable of being
drawn to a diameter of 0.78 mm or larger with 0.5 or fewer breaks per
ton; and (vii) containing by weight the following elements in the
proportions shown: (1) 0.78 percent or more of carbon, (2) less than
0.01 percent of soluble aluminum, (3) 0.040 percent or less, in the
aggregate, of phosphorus and sulfur, (4) 0.008 percent or less of
nitrogen, and (5) either not more than 0.15 percent, in the aggregate,
of copper, nickel and chromium (if chromium is not specified), or not
more than 0.10 percent in the aggregate of copper and nickel and a
chromium content of 0.24 to 0.30 percent (if chromium is specified).
For purposes of the grade 1080 tire cord quality wire rod and the
grade 1080 tire bead quality wire rod, an inclusion will be considered
to be deformable if its ratio of length (measured along the axis - that
is, the direction of rolling - of the rod) over thickness (measured on
the same inclusion in a direction perpendicular to the axis of the rod)
is equal to or greater than three. The size of an inclusion for
purposes of the 20 microns and 35 microns limitations is the
measurement of the largest dimension observed on a longitudinal section
measured in a direction perpendicular to the axis of the rod.
The designation of the products as ``tire cord quality'' or ``tire
bead quality'' indicates the acceptability of the product for use in
the production of tire cord, tire bead, or wire for use in other rubber
reinforcement applications such as hose wire. These quality
designations are presumed to indicate that these products are being
used in tire cord, tire bead, and other rubber reinforcement
applications, and such merchandise intended for the tire cord, tire
bead, or other rubber reinforcement applications is not included in the
scope. However, should petitioners or other interested parties provide
a reasonable basis to believe or suspect that there exists a pattern of
importation of such products for other than those applications, end-use
certification for the importation of such products may be required.
Under such circumstances, only the importers of record would normally
be required to certify the end use of the imported merchandise.
All products meeting the physical description of subject
merchandise that are not specifically excluded are included in this
scope.
The products under this order are currently classifiable under
subheadings 7213.91.3011, 7213.91.3015, 7213.91.3020, 7213.91.3093,
7213.91.4500, 7213.91.6000, 7213.99.0030, 7213.99.0090, 7227.20.0030,
7227.20.0080, 7227.90.6010, 7227.90.6020, and 7227.90.6085 of the HTSUS.
Although the HTSUS subheadings are provided for convenience and customs
purposes, the written description of the scope of this proceeding is dispositive.
Sources: 67 FR 65945 (October 29, 2002) order; and 68 FR 64079 (November 12, 2003)
changed circumstance review. HTSUS numbers for some of the products covered by the scope have changed several times since these documents were published.
Note that HTSUS numbers are subject to change.
|